Which side of the plasterboard do you cut? Plasterboard is cut to length by first marking then scoring a line on the face side of the board with a straight edge and Stanley knife. Then, lift the sheet off the floor and snap the board along the score line.

Which is the right side of plasterboard to use?

Dewy New Member. The white side is for taping the joints then a light skim with mud on the joints then its ready to paint. The grey side is for plastering on top.

Does it matter which way you install plasterboard?

One of the key things to remember when tackling this job is to hang your plasterboard horizontally rather than vertically. Because of the way the boards are manufactured, they have a 'grain' along their length, which means that the best strength is achieved when they're secured perpendicular to the studwork.

What is the difference between gyprock and plasterboard?

The short answer is not much.

Gyprock is also known as gypsum board, drywall, or plasterboard. For thousands of years, plaster made from lime, sand, animal hair and other ingredients was used to create a smooth interior finish on building walls and ceilings.

Should plasterboard be fitted horizontally or vertically?

Which way up should I install plasterboards? When installing a single layer of Gyproc plasterboard, it's best to hang boards vertically. This is standard practice in the industry, and complies with BS 8212. We don't recommend installing boards horizontally as this affects lateral stability performance.

How to cut Drywall | How to cut plasterboard

Can you hang plasterboard vertically?

On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. However, on residential jobs, the drywall on the walls is typically hung horizontally.

Do you plaster over plasterboard?

If you've attached plasterboard, or drylining you have the choice of either painting or decorating straight onto the board, or finishing with a layer of skim plaster. The skim tends to be favoured because it provides a superior finish, and it adds an extra layer of sound proofing.

Is it OK to paint directly onto plasterboard?

Definitely make shure your plasterboard is sealed properly prior to painting. Give the walls a light sand and mistcoat with a mix of Matt emulsion and clean water. ... There is no difference to painting plaster board to skimmed surfaces. Use a decent quality roller and wash it out thouoghly before you use it.

What is the easiest way to cut drywall?

Use a pencil to draw a scoring line. With a sharp utility knife or other cutting tool, follow the pencil line and lightly cut through the paper layer of drywall. Tip: The best tools for cutting drywall are utility knives, putty knives, reciprocating saws, oscillating multi-tools and track saws with dust collectors.

Is there a right and wrong side to plasterboard?

Most common plasterboards come with the option of either tapered edge or square edge. ... Most standard plasterboard has one ivory face and one brown. The liner on the ivory face is specially designed for plastering plaster should not be applied to the brown reverse face.

Why does plasterboard have a tapered edge?

Tapered edge plasterboard is most commonly used for walls and features a narrower edge profile, making it better suited for either jointing or skimming. Plasterboard with a tapered edge makes it easier to achieve a seamless finish between sheets, providing a sturdy, even base upon which to plaster.

Do you leave a gap between plasterboard?

The gap is recommended for the edge of inside corner pieces that you need to cut. This is because if you cut it a little too wide, you can mess up the edge forcing it into place. It does NOT recommend gaps between full sheets.

How do you stagger plasterboard joints?

Staggering seams refers to installing the panels so that butt joints are not aligned between adjacent rows of panels. A simple method for staggering seams is to start the first row with a half-panel and start the second row with a full-length panel, continuing this alternating pattern for the rest of the installation.

Do you drywall the ceiling first?

When hanging drywall, always hang the ceiling first. This is the hardest drywall to hang, so get a partner and go slow. Large cracks due to misaligned sheets are hard to repair because the extra mud required to fill them will constantly fall out and drop to the floor (or worse, down the back of your neck!).

How do you layout drywall?

1. 1 - Bound Edges should pair with Bound-Edges and Butts with Butts. The bound edge is the long edge of a sheet of drywall. ...
2. 2 - Hang Drywall Sheets Perpendicular to Studs. ...
3. 3 - Stager the Butt Joints. ...
4. 4 - Ceiling to Floor and Left to Right.

Can you store plasterboard on its side?

It's stored on it's side (beveled edge up/down) all the time on job sites. Just make sure to protect bottom edge and keep it off the ground if there's a moisture risk.

Can I cut plasterboard with a jigsaw?

Conclusion. To conclude, using a jigsaw to cut drywall is easy, provided you have the right assisting tools for the job. A utility knife saw blade, drill with a drill bit, marking tools, and drywall rasp are all helpful when it comes to cutting sheetrock.